How to Clean a Wine Cooler, Step by Step
To clean a wine cooler, unplug it, move the bottles somewhere cool, take out the shelves, and wipe the inside with a mild solution of baking soda and warm water. Dry everything completely, clean the door gasket and, on compressor models, vacuum the condenser coils. Then let the empty cooler get back to temperature before you reload it.
How often to clean it
Wipe up spills and drips as soon as you notice them. Spilled wine gets sticky and can start to smell if it is left to sit.
Beyond that, a full interior clean once or twice a year is enough for most households, or any time you notice an odor. Many manufacturers suggest cleaning the condenser coils on compressor units periodically, often somewhere between every few months and once a year depending on how dusty the room is. Homes with pets usually need it more often. Your manual will give the interval for your model.
Step-by-step interior clean
- Unplug the cooler. Do this before you touch anything inside, and especially before you go near the fan or the coils.
- Move the bottles. Put them somewhere cool and dark for the few hours this takes: a second cooler, an interior closet or a picnic cooler with a couple of ice packs wrapped in a towel. A short stretch at cool room temperature will not harm the wine. How to store wine without a wine cooler has more options if you need them.
- Take out the shelves. Note how they come out so they go back the same way. Wipe wooden shelves with a damp cloth and dry them right away; do not soak them, since wood can warp or crack. Metal racks can be washed in warm, soapy water.
- Wash the interior. Mix about a tablespoon or two of baking soda into a quart of warm water. Wipe down the walls, floor and ceiling with a soft cloth or sponge. Baking soda cleans and helps neutralize odors without leaving a scent of its own.
- Rinse and dry. Wipe again with a cloth dampened in plain water, then dry every surface with a clean towel. Leave the door open for a while so any remaining moisture can evaporate.
What to avoid
Skip bleach, ammonia, abrasive powders and scouring pads. They can damage plastic liners and finishes, and the fumes linger in a closed cabinet. Also avoid strongly scented cleaners. Many wine storage guides warn that strong odors in an enclosed space can affect corked bottles over time, and at the very least, nobody wants to open the door to a lemon-pine smell. Mild dish soap and water is fine for stubborn sticky spots.
The door gasket and the glass
The rubber gasket around the door is easy to overlook, but it is what keeps cold air in. Dirt and sticky residue in its folds can stop it from sealing properly.
- Wipe it with warm, soapy water and a soft cloth. A soft old toothbrush helps get into the grooves.
- Dry it thoroughly. Moisture trapped in the folds is a common place for mold to start.
- While you are there, check for tears or flattened sections. If a sheet of paper slides out easily when closed in the door, the seal may need attention.
For the glass door, plain water or a mix of water and a little white vinegar works on the inside and leaves no strong smell. A regular glass cleaner is fine on the outside. Use a soft cloth rather than paper towels or anything abrasive, which can scratch the glass or any coating on it. Stainless steel trim can be wiped with a damp cloth in the direction of the grain and dried.
Coils and vents on compressor models
Compressor coolers release heat through condenser coils. When those coils are coated in dust, the cooler works harder, runs longer and may struggle to hold temperature.
- On rear-venting (freestanding) models, the coils or vents are usually on the back. Pull the unit out carefully, unplug it and vacuum the coils with a brush attachment.
- On front-venting (built-in) models, the vents are behind the grille at the bottom front. Your manual will show whether the grille comes off and how to reach the coils.
- Go gently. Coils and fins bend easily.
Thermoelectric coolers do not have condenser coils, but they do have a heat sink and fan, usually at the back. Vacuum any dust from the vents there too.
Some compressor models also have a small drain hole at the back of the interior and a drip pan near the compressor. If yours does, make sure the drain is clear and the pan is clean.
Dealing with odors and mold
If a smell remains after cleaning, find the source first. Common culprits are spilled or leaking wine under a shelf, a weeping cork, or mold on the gasket or on wooden shelves.
For lingering odors, leave an open box of baking soda or a small dish of activated charcoal inside for a few days. Both absorb odors without adding any.
For small spots of mold, wipe the area with a solution of white vinegar and water, then dry it completely. Mold usually points to too much moisture, so check the gasket and look for condensation. Wine cooler humidity explains what level is reasonable. Mold that keeps coming back on a gasket is a sign the gasket may need replacing.
Let it come back to temperature before reloading
Once everything is dry and the shelves are back in place, plug the cooler in and close the door. Let it run empty until it reaches your set temperature. That often takes a few hours, and longer in a warm room. A thermometer in a glass of water on a middle shelf gives you a more reliable reading than the display alone.
When you reload, put the bottles back in the same zone and rough positions they came from. It saves you hunting for a bottle later, and it keeps the wines you meant to keep at serving temperature where you expect them.